They’ve been on now for 6 months and still look great. Easy to cut and install.

I waited a few weeks to write this review so I could give my honest opinion. It looks amazing, I’ve had some people ask me if I installed real tile. It’s a VERY thick rubber, so you’re not going to be getting that cheap dollar store stuff. I haven’t had any issues with peeling. I’m assuming people who are having peeling issues didn’t degrease their wall and seal it with a heat gun after install. I scrubbed the area I installed the tile with undulated rubbing alcohol. After installing it I ran over all of the tile with a heat gun and pressed it down firmly. I haven’t had any issues with it. It’s very easy to clean/wipe down too. It also IS rated to be above stoves. Some backsplash cannot be installed by stoves due to heat, this one CAN.

À ne pas acheter. On s'est fié aux bons commentaires, mais malheureusement le produit a commencé à décoller à plusieurs endroits même pas 3 jours après son installation. Là c'est de pire en pire à chaque jour de nouveaux endroits décollent. C'est dommage autant pour l'argent et le temps qu'on a investi. On aura pas le choix de tout retirer et de poser la vrai céramique , car ce produit ne fonctionne pas. À éviter!!

For the price, was expecting them to stick but no... washed the walls and lightly sanded but they still pealed off.They are really nice though

I found these apply best starting from the bottom and working your way up. That way everything adheres smoothly. I have a bunch of screw holes and marker on the wall and these covered it up nicely. Cut easily with a box cutter. I messed one piece up and it was still very sticky after I reapplied it.

Has a rubberized texture, easy to do and its help up for a few months now, really livened up the kitchen

Ça a donné un petit style très sympa à cet endroit de ma cuisine.L’adhésif est vraiment performant, un petit côté 3D qui donne un peu de relief, et une jolie couleur/motif.Un peu chiant à poser quand on a pas l’habitude mais ça vaux le coup.Ça a l’air d’être de bonne qualité, j’en suis vraiment contente.

I found these tile covers easy to apply and they have great adhesion to the wall. I installed them a month ago and I haven't had any problems with them peeling off

I could rave about this tile all day!! Wow. It looks phenomenal. You cannot tell at all that this is not real tile. The adhesion is very strong. I've had it installed for almost 3 months now and not one edge or corner has come up. I ordered a small exacto knife to make cuts, but used scissors as well with success, used a sharpie pen on the peel off plastic cover that's on each sheet to mark where I needed to make my cuts. There were a few places where I needed to put an odd piece in or part of a piece to finish off a section and you can't tell unless you get really close. They are super easy to wipe off with a damp sponge. The spot behind our toaster oven has not been affected at all by the heat (back of oven is probably a foot away from wall). The tiles look beyond amazing!! If you're on the fence, definitely give it a try. Would recommend to anyone!

They look nice, go on fairly easy. The only negative was they don't peel from the ear backing very easily. Pull too fast or too slow and the tile rips. Had to throw some out because once they tear you're not getting the tile off the backing without ripping it further. I didn't need all of the tiles in the package so it wasn't a big concern but if your buying, buy extra and bank on having to toss a few

There are a lot of reviews on here, many with some useful info on whether these will be right for you. The sales description is very accurate, so I will just concentrate on what I found with these tiles.... I bought the marbly effect with darker tiles in them.Things note worthy:The darker ones are not black, they are a medium/dark grey, as well as lighter shades.The surface needs to be flawlessly clean or expect problems in the coming hours, days or weeks. I had multiple surface to adhere to, and whilst these will instantly grab any surface, they can peel or bubble if the surface is not properly prepared. I used an IPA spray (alcohol) as it removes greasy marks. If you have a good surface - these stick like sh....They are hard to cut.... not in the sense that you need a power saw to cut through them, but you will need a good Stanley knife blade (or several depending on quantity of tiles needed). You can slice through the grout effect areas like butter, but the raised tiles areas will take 2-6 pass throughs to cut effectively, depending on how hard you press. Don't be a hero, use firm but not arm shaking force to score them for a better finish. TIPS - use new blades for a perfectly clean cut.You can use scissors as well, but a knife blade gives a more accurate, clean cut on intricate areas.I have seen photos of people using these as backsplashes on a hob.....You are idio...... These are made from vinyl and is therefore a fire hazard. Don't lay these behind a hob!I bought various designs of these things from various companies before deciding on these.... I wanted a matt effect, but most were a gloss finish. These are a gloss finish, and in a way I now prefer that as they are easier to clean. There are loads of ads with photos that give an appearance of a matt finish, but they are not - just enticingly good photography - not that I'm a cynic!Corners - So I had inward and outward corners to contend with and tried all methods. By far the simplest is to cut into a corner. If you are not using something like PVC angle or other decorative 'disguises', then it can be a little tricky if your walls are not true. My walls were compulsive liars! They were out in every possible direction making 'cut in' corners difficult. Outer corners - yes you can fold these around corners. I had 4 of these. two I just folded alone, one I used spray adhesive, and another I used lots of spray adhesive! So a common area is the window recess area. a 90 degree bend. The first couple I just peeled and stuck around the corner, but the following day I noticed some minor bubbling right on the edge. I was able to drip some spray adhesive down the gap though. As with the glue instructions, spray it or drip it in a bubble gap and allow to go tacky for a 2-4 minutes before pushing down.... I did have one that persistently kept bubbling and I can only presume that I didn't prepare the area good enough.... NOTE - be careful if you rub hard to get a good clean 'fold' on the corner as you can split the vinyl if done too much... It will take some doing to actually crack though, so you can be quite forceful. Inner corners - again, I had 4 of these. much similar to the outer but you just need to be aware of the remaining tile (the bit going around the corner) Don't peel the protective backing off more than needed as they will grab any surface you accidently touch whilst trying to get a good push in the corner. As an example, if I had a whole tile needing to go around a corner, I would stick the nearest edge up to the corner - that way the tile is bonded and wont move. I then used my finger tips to push into the corner (hard). I then used a block of wood to get a good even and solid push into the corner, before removing the backing off the second half... NOTE - If your walls are not true, just remember that when you go around the corner, the tile may end up with the tile level changing and having a slight slope up or down. So, if your walls are waaaaaay out , I would recommend cutting into a corner. I did mess up in the beginning and started in the wrong corner. This led to coincidentally one of the tiles finishing in a corner.... However, as these tiles are staggered on every row, it meant that I had to fold some of the rows from the next tile around the corner. I was a bit worried that having only approx. 5 cm going around the corner would not be enough to hold it in perpetuity.... This corner was also waaaay out of alignment. It is a mainly hidden corner, so rather than removing a row of about 5 tiles (£15 worth), I actually folded the other tile around the corner and over lapped the other tile by about 10cm, laying one tile on top of the other..... If you can align them well, it doesn't overly show, and sticking these tiles on top of each other is probably the best surface to stick to! This gave me a stronger corner bond which won't be seen anyway and saved removing a whole row...... a learning curve tbh.... I wouldn't ordinarily do this type of thing but as it was out of sight, it didn't matter.Once you have done the tiling (if that's what you can call it)..... I used a tea towel and rubbed over the tiles every day for a couple of days to assist any air bubbling that may have occurred. You could use spray adhesive (carpet glue).... I bought 8 cans thinking that I would spray them all, but didn't need 7 of them as I put a lot of work into the prep. These are extremely grab sticky if the surface is perfect!My final observation/tip - I have OCD.... and when you are up close and personal cutting and sticking these to the wall, you can see every blemish, misalignment, bump bla bla..... (I am being extremely critical of minor issues.....my self-adhesive tiling is not that bad!!!) If you are thinking it is not perfect - step back and look at it. No one is going to be checking your tiles with a spirit level or magnifying glass, and you would have to be some sort of tiling genius to get perfect 'real' tiles, so some imperfections can actually enhance the look. Removing these tiles because it is not quite right is a 70/30 pot luck (depending on the backing surface as to whether the tile comes off clean enough to re-use, or if it has taken any paint or plaster with it..... so think twice before taking off.If you need to remove the tiles, a good way (even if used spray adhesive) is to warm the tiles up using a hair dryer, or steam wallpaper stripper, or if careful - a heated paint stripper. It will leave a residue, but should leave the walls intact!You can drill these. I would suggest that you use a wood/universal drill first (through the tile bit) if going into concrete. Once you have created a hole, then swap to a masonry drill. Just remember, these are essentially stickers, so if you are needing a hole near an edge of a tile, be careful as there is a chance you could snag the tile and pull it if you are using a blunt or slow speed drill.These are water resistant. You can wipe them down with a damp cloth and even spray with a bit of anti bac....... but they are not waterproof to the degree that putting them around a hot steamy shower will stop them peeling off. Invariably, at some point, they are likely to peel. Yes they will look great for a while , but if you want these to last (which they can) then don't put in wet areas.One final comment - every tile is 100% accurate and symmetrical to the next one in every way.... I noticed a darker area on one of my join areas which was annoying, and got me muttering about poor quality tiles..... then I noticed that a small bit of the FRONT protective film had not come off when I originally removed it. Luckily I noticed before ripping the tile off...Oh one more final comment - I can't reiterate enough - don't use this behind a hob.... It's dangerous! Yes, it will look lovely, but even if the kitchen doesn't catch fire at some point, invariably you are likely to ruin the tiles over time with the likes of fat splashing up on them etc.... buy a proper splashback for a hob.Hope that has helped answer some of the questions you have, like I did before deciding to buy these.

ho preso questo prodotto per rifinire sopra il lavabo nella saletta disinfezione di un negozio di parrucchiera , dopo aver imbiancato il muro ho applicato questo adesivo con molta facilita' , per mestiere faccio tutt'altro quindi non ho molta manualita', ho impiegato poco tempo per fare una bella cornice h. 30cm tutto intorno ;l'adesivo prende molto bene lo spessore della piastrella e' tale da dare la giusta rigidita' in modo da applicarla con facilita' senza pieghe , ho ritagliato con una forbice tipo elettricista per andare attorno al rubinetto , il risultato e bello esteticamente ed il muro e' protetto dai schizzi d'acqua , missione riuscita!