Your cart is empty.
Your cart is empty.Product Description
FEATURES
- The front wheel drive bearing tool kit comes with all the tools you need to make removal and installation a breeze.
- Works with front-wheel drive hub bearing assembly parts on most front-wheel-drive American domestic and imported cars and small pickup trucks.
- Including multiple sizes of drifts, and the kit can be used for different models.
-With storge case. -Material: carbon steel for tools, ABS plastic for case
PRODUCT DESCRIPTION
INSTRUCTIONS
Step.1 Determine if the vehicle has a trapped rotor or a floating rotor.
Step.2 Assemble the tool components, and press out the worn bearing.
Step.3 Lightly lubricate the new bearing, and position it for installation with the tool
components assembled. Press the bearing into the spindle assembly until it bottoms.
Step.4 Fasten the bearing retainer in place using the bearing retainer bolts. (On Neon vehicles, install the snap ring in the knuckle.)
Step.5 Assemble tool components. Lightly oil the hub assembly, and install the hub. Attention: The bearing installer must be assembled with the flat side toward the bearing and the small diameter pilot on the side away from the bearing.
Step.6 Assemble the remaining vehicle components that were removed for bearing replacement: (1)lower ball joint to steering knuckle assembly brake rotor. (2)disc brake caliper. (3)outer tie rod nut and tie rod. (4)axle nut. (5)front tires.
H. Wright
Reviewed in the United States on August 29, 2024
I have not done the job yet .. but verified whether this fits my needs and it does (2009 ford escape 4wd rear wheel bearing - it’s giant to me)I will update after use with quality feedback .. this includes the stars as well
jk
Reviewed in Canada on May 8, 2024
the threaded bolt to run the tool is not the greatest quality if bearings are seized it strips when using a impact wrench and your changing bearings because there bad and stuck hard in most cases
larry kreiser
Reviewed in Canada on May 23, 2024
Easy to use
Trevor Tremblett
Reviewed in Canada on March 27, 2024
Great tools
Stacey Heintzman
Reviewed in Canada on February 18, 2024
Very poor quality, first time we used it , which was on an ATV wheel bearing, and it broke ...
eddie g miller
Reviewed in the United States on October 18, 2024
good.
Customer
Reviewed in the United States on January 11, 2024
Worked on my 2000 Honda Civic. Only problem is this tool doesn't take off the hub it needs to be hammered out, then this tool can be used to remove and replace the bearing and then use it to press the hub back in.
Piranha8U
Reviewed in Canada on September 4, 2023
Used light oil on threads. Only concern is the long nut is not full thread, but it worked as intended. Better then the 20 ton hydraulic press that I built.
ronald culbertson
Reviewed in the United States on December 18, 2023
This product was very good I was very happy
Old Faithful
Reviewed in Canada on November 3, 2023
Kit is fairly complete, except for the lack of a hub removal jig.As others have pointed out, the kit comes with a coarse threaded, unmarked forcing bolt and simple washers as bearing surfaces, which tend to fail under strain. I replaced the original 10 TPI coarse threaded screw with a grade 8 fine threaded one with deep nut, which translates into a 60% increase in forcing pressure and a signifcantly greater shear resistance compared to regular grade steel bolts. I then added some thrust ball bearings to reduce friction on the bearing surfaces and lubricated everything with extreme pressure grease and it worked great on my 20 year old Honda Civic that lived all its life in the Salt Belt.Although the removal strain maxed out my heavy electric impact gun and the forcing nut got hot in use, there was no observable wear on the threads.These vast improvements only cost me an extra $20 and turned a cheap kit into one superior to another that sells for $50 more and whose only improvement is to come with an extra ungraded coarse threaded forcing screw.As for the other components in the kit, they are very heavy, worked flawlessly, without any signs of strain and suffered no visible damage in the process.
Colin
Reviewed in Canada on November 26, 2023
Saved big money buying this kit and doing my own bearing, held up fine.
CUBANO100%LATINO
Reviewed in the United States on January 18, 2023
Tool was awesome, just use plenty of grease on the main screw and nut and let me tell you I use my 1200 ft lb impact and the removal and installation of the bearing were a breeze. Make sure line up stray if it is a little off just stop and adjust and plenty of grease this tool wont loose tread. Excellent tool.
Mark
Reviewed in Canada on November 3, 2022
a+++
Recommended Products