Your cart is empty.
Your cart is empty.Two handle roman tub valve adjustable 1/2" CC connection
anne kenny
Reviewed in Canada on September 21, 2024
The main faucet had the seal missing, factory defect.we return and amazon is crediting my account.
333 Fabrication 1/2 evil
Reviewed in the United States on February 8, 2024
Ordered to replace a leaking valve body. Much less expensive than replacing the entire fixture. Had it professionally installed. Working as it should.
Susan Smithson
Reviewed in the United States on February 16, 2024
Used for renovation and works great
Tim Hill
Reviewed in Canada on October 22, 2024
Was delivered ahead of schedule and was of good quality.
Vipun
Reviewed in Canada on December 2, 2022
Bought for renovation and use it work great as support to
Dan
Reviewed in Canada on May 15, 2021
This item came as described and installed quite easily.
mary
Reviewed in Canada on April 22, 2021
We returned it due to project update.
Tien Dang
Reviewed in Canada on August 29, 2020
I did not install this but it works well with my Moen roman tub faucet.
K from NJ
Reviewed in the United States on March 26, 2018
Worked perfectly in my case. Other reviewers noted that their item seemed to be used. In my case, the solder work and general appearance of the lower parts of the valve looked like they had a sloppy solder job. But I don't believe it is a used valve. Whatever process they have to make this was not designed for a pristine appearance. I was concerned, but the pre-soldered joints did not leak at all.Also be aware that this particular valve does not include the aggressive clamping system under the deck. The image also do not show that system either. They show what you get. Two nuts and a washer for each valve body. That said, the valves hold just fine on the 2x6 based deck I built.At least one other reviewer mentioned the tubing was not aligned properly with the valve body. Either straight or perpendicular depending on which tube it was. On my valve they tubes were very close but not perfectly aligned. But I did not have any issues as a result.One other detail is that the tubing on this valve appears to be brass. Not copper. I was concerned about how the solder would hold but it did in fact hold fine. No leaks. I used a simple lead free solder and flux kit I bought at Home Depot with Map gas.When soldering this valve keep in mind the plastic cartridges can not be removed. So don't apply excessive heat and cool off the valve with something wet when you're done. I'm an amateur...(at best)... but this piece of advice from experts is worth knowing.So for function I think this is a fine valve. For finish? Not so much. I took away one star because it shouldn't look like they threw it off a mountain after making it. Appearance
Yanick Thibault
Reviewed in Canada on February 18, 2018
Work well, easy to install
Steve
Reviewed in Canada on December 28, 2017
Cheap catrridges in these that leak and drip. Replaced 4 times as Moen Warentee but they still drip. I will tru and return to amazon or the seller.
MD
Reviewed in the United States on December 31, 2015
A valve is a valve, but here is what I like about this one. First the nozzle can be located remotely. In my install I put the valves where they would be conveniently reached when out or in the tub. The nozzle is remotely located near the drain of a fairly long tub. The other reason I like this valve is that it is Moen. They really do take care of their customers with a lifetime warranty on valve inserts as well as the finish of whatever trim kit you order. You may pay a little more , but it is the last one you will buy. Moen gives me a very old school, high quality, American made experience. I wont buy any other brand.
DPS
Reviewed in the United States on May 31, 2013
Worked out great! Specs said it was for a 10" spread and my tub was only 8" so I was a little concerned. However, I tube cut aninch off both horizontal pipes. I traced the hole pattern from the tub on to a scrap piece of wood and drilled the holes out. Dry fitted it all together, soldered it, and slipped it into tub (Was no room to solder under tub). I ended up using 2 Shark Bite fittings- 1/2" to 3/4" thread and a couple of supply lines to the cut-off valves. Pressure tested all. No leaks! Installed trim kit. Plenty of water volume and pressure. As they say, buy it for looks, buy it for life.
Recommended Products
